Compilation and Installation using Autoconf

1. Basic Usage

2. Driver Options

   • Xlib Driver Options
   • DRI Driver Options
   • OSMesa Driver Options

ATTENTION:

The autotools build is being replaced by the meson build system. If you haven't yet now is a good time to try using meson and report any issues you run into.

1. Basic Usage

The autoconf generated configure script can be used to guess your platform and change various options for building Mesa. To use the configure script, type:

    ./configure

To see a short description of all the options, type ./configure --help. If you are using a development snapshot and the configure script does not exist, type ./autogen.sh to generate it first. If you know the options you want to pass to configure, you can pass them to autogen.sh. It will run configure with these options after it is generated. Once you have run configure and set the options to your preference, type:

    make

This will produce libGL.so and/or several other libraries depending on the options you have chosen. Later, if you want to rebuild for a different configuration run make realclean before rebuilding.

Some of the generic autoconf options are used with Mesa:

--prefix=PREFIX

This is the root directory where files will be installed by make install. The default is /usr/local.

--exec-prefix=EPREFIX

This is the root directory where architecture-dependent files will be installed. In Mesa, this is only used to derive the directory for the libraries. The default is ${prefix}.

--libdir=LIBDIR

This option specifies the directory where the GL libraries will be installed. The default is ${exec_prefix}/lib. It also serves as the name of the library staging area in the source tree. For instance, if the option --libdir=/usr/local/lib64 is used, the libraries will be created in a lib64 directory at the top of the Mesa source tree.

--sysconfdir=DIR

This option specifies the directory where the configuration files will be installed. The default is ${prefix}/etc. Currently there's only one config file provided when dri drivers are enabled - it's drirc.

--datadir=DIR

This option specifies the directory where the data files will be installed. The default is ${prefix}/share. Currently when dri drivers are enabled, drirc.d/ is at this place.

--enable-static, --disable-shared

By default, Mesa will build shared libraries. Either of these options will force static libraries to be built. It is not currently possible to build static and shared libraries in a single pass.

CC, CFLAGS, CXX, CXXFLAGS

These environment variables control the C and C++ compilers used during the build. By default, gcc and g++ are used and the debug/optimisation level is left unchanged.

LDFLAGS

An environment variable specifying flags to pass when linking programs. These should be empty and PKG_CONFIG_PATH is recommended to be used instead. If needed it can be used to direct the linker to use libraries in nonstandard directories. For example, LDFLAGS="-L/usr/X11R6/lib".

PKG_CONFIG_PATH

The pkg-config utility is a hard requirement for configuring and building mesa. It is used to search for external libraries on the system. This environment variable is used to control the search path for pkg-config. For instance, setting PKG_CONFIG_PATH=/usr/X11R6/lib/pkgconfig will search for package metadata in /usr/X11R6 before the standard directories.

There are also a few general options for altering the Mesa build:

--enable-debug

This option will set the compiler debug/optimisation levels (if the user hasn't already set them via the CFLAGS/CXXFLAGS) and macros to aid in debugging the Mesa libraries.

Note that enabling this option can lead to noticeable loss of performance.

--disable-asm

There are assembly routines available for a few architectures. These will be used by default if one of these architectures is detected. This option ensures that assembly will not be used.

--build=

--host=

By default, the build will compile code for the architecture that it's running on. In order to build cross-compile Mesa on a x86-64 machine that is to run on a i686, one would need to set the options to:

--build=x86_64-pc-linux-gnu --host=i686-pc-linux-gnu

Note that these can vary from distribution to distribution. For more information check with the autoconf manual. Note that you will need to correctly set PKG_CONFIG_PATH as well.

In some cases a single compiler is capable of handling both architectures (multilib) in that case one would need to set the CC,CXX variables appending the correct machine options. Seek your compiler documentation for further information - gcc machine dependent options

In addition to specifying correct PKG_CONFIG_PATH for the target architecture, the following should be sufficient to configure multilib Mesa

./configure CC="gcc -m32" CXX="g++ -m32" --build=x86_64-pc-linux-gnu --host=i686-pc-linux-gnu ...

2. GL Driver Options

There are several different driver modes that Mesa can use. These are described in more detail in the basic installation instructions. The Mesa driver is controlled through the configure options --enable-glx and --enable-osmesa

Xlib

It uses Xlib as a software renderer to do all rendering. It corresponds to the option --enable-glx=xlib or --enable-glx=gallium-xlib.

DRI

This mode uses the DRI hardware drivers for accelerated OpenGL rendering. To enable use --enable-glx=dri --enable-dri.

--with-dri-driverdir=DIR

This option specifies the location the DRI drivers will be installed to and the location libGL will search for DRI drivers. The default is ${libdir}/dri.

--with-dri-drivers=DRIVER,DRIVER,...

This option allows a specific set of DRI drivers to be built. For example, --with-dri-drivers="swrast,i965,radeon,nouveau". By default, the drivers will be chosen depending on the target platform. See the directory src/mesa/drivers/dri in the source tree for available drivers. Beware that the swrast DRI driver is used by both libGL and the X.Org xserver GLX module to do software rendering, so you may run into problems if it is not available.

--disable-driglx-direct

Disable direct rendering in GLX. Normally, direct hardware rendering through the DRI drivers and indirect software rendering are enabled in GLX. This option disables direct rendering entirely. It can be useful on architectures where kernel DRM modules are not available.

--enable-glx-tls

Enable Thread Local Storage (TLS) in GLX.

--with-expat=DIR

DEPRECATED, use PKG_CONFIG_PATH instead.

The DRI-enabled libGL uses expat to parse the DRI configuration files in ${sysconfdir}/drirc and ~/.drirc. This option allows a specific expat installation to be used. For example, --with-expat=/usr/local will search for expat headers and libraries in /usr/local/include and /usr/local/lib, respectively.

OSMesa

No libGL is built in this mode. Instead, the driver code is built into the Off-Screen Mesa (OSMesa) library. See the Off-Screen Rendering page for more details. It corresponds to the option --enable-osmesa.

--with-osmesa-bits=BITS

This option allows the size of the color channel in bits to be specified. By default, an 8-bit channel will be used, and the driver will be named libOSMesa. Other options are 16- and 32-bit color channels, which will add the bit size to the library name. For example, --with-osmesa-bits=16 will create the libOSMesa16 library with a 16-bit color channel.

3. Library Options

The configure script provides more fine grained control over the libraries that will be built.